PCB Libraries Forum Homepage
Forum Home Forum Home > PCB Footprint Expert > Questions & Answers
  New Posts New Posts RSS Feed - Is There a Way To Go Back to LP Wizard Silkscreen?
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Is There a Way To Go Back to LP Wizard Silkscreen?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Alphatronique View Drop Down
New User
New User
Avatar

Joined: 25 Aug 2012
Location: Canada
Status: Offline
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alphatronique Quote  Post ReplyReply Direct Link To This Post Topic: Is There a Way To Go Back to LP Wizard Silkscreen?
    Posted: 08 Jan 2013 at 8:07pm
Hi 

i see that it have a 7351B.dat  ,but did it have a way to got back old style silkscreen output
as it was whit older "B"  ?

"personally" i like to see orientation marking under package ,it easy to see when 
program pick&place and or rework  ,and still keep a small dot if need post assembly

and also when work on old design and add new part  you have 2 different "standard"
and not to forgot pin 1 position change that screw machine programming scrip ..

so think it may good to have check-box or else for got to older style

Best regard
Marc L.
Back to Top
Back to Top
Tom H View Drop Down
Admin Group
Admin Group
Avatar

Joined: 05 Jan 2012
Location: San Diego, CA
Status: Offline
Points: 5718 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tom H Quote  Post ReplyReply Direct Link To This Post Posted: 08 Jan 2013 at 8:15pm

Here are the basic IPC-7351C silkscreen rules –

 

1.     No silkscreen outline under the component; these get covered up during assembly and don’t provide any useful purpose (waste of expensive inkjet cartridges)

 

2.     All silkscreen outlines visible after assembly process and provide a functional use as alignment marking for assembly registration accuracy

 

3.     All silkscreen outlines must be inside placement courtyard

 

4.     All Silkscreen outlines are mapped to the Maximum Component Body with 1 exception, the Silkscreen to Pad spacing rule “overrides” the Component Body Mapping.

 

5.     Silkscreen outlines should map the component body and not go around pads. Excess silkscreen outlines should be avoided to make room for ref des locations. Silkscreen outlines should perform a “hatch” outline along the component package body.

 

6.     Pin 1 is identified by extending the silkscreen along Pin 1 length to indicate polarity when the package cannot be placed inverted (inverted parts include non-polarized 2-pin parts)

 
The IPC-7351B Default Preferences are strictly Pin 1 location in "Upper Left".
 
Download the new IPC-7351C Zero Component Orientation guidelines here -
 
Back to Top
Mattylad View Drop Down
Advanced User
Advanced User
Avatar

Joined: 02 Jun 2012
Location: Lancashire UK
Status: Offline
Points: 152 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mattylad Quote  Post ReplyReply Direct Link To This Post Posted: 10 Jan 2013 at 2:45pm
What does:
Quote Silkscreen outlines should perform a “hatch” outline along the component package body.

mean?

ISTR Hatched outlines indicates it is mounted on the other side of the board or removable.
Back to Top
Tom H View Drop Down
Admin Group
Admin Group
Avatar

Joined: 05 Jan 2012
Location: San Diego, CA
Status: Offline
Points: 5718 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tom H Quote  Post ReplyReply Direct Link To This Post Posted: 10 Jan 2013 at 2:58pm
The silkscreen outline defines the component package body and does not go near or around any pads.
 
So the Silkscreen Hatch Marks would only appear where the component body is and no component leads.
 
However, the silkscreen outline does extend to identify Pin 1 location.
 
An example is a simple Quad Flat Package. The brown line = the max component body outline.
 
The silkscreen does not go around or near any pads except Pin 1.
 
The silkscreen outline is referred to as Crop or Hatch marks. It's a USA term.
 
 
Back to Top
Alphatronique View Drop Down
New User
New User
Avatar

Joined: 25 Aug 2012
Location: Canada
Status: Offline
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alphatronique Quote  Post ReplyReply Direct Link To This Post Posted: 11 Jan 2013 at 8:26am
Hi Tom 

i read whit great attention the new 7351C proposal 
and make some test on some specific footprint

and still personally not ready yet to move to new 7351C 
so still think it may great to have both old and new style for silk option
on footprint expert Big smile

Best regard and you make great work  
Marc L.
Back to Top
Tom H View Drop Down
Admin Group
Admin Group
Avatar

Joined: 05 Jan 2012
Location: San Diego, CA
Status: Offline
Points: 5718 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tom H Quote  Post ReplyReply Direct Link To This Post Posted: 11 Jan 2013 at 8:50am
We'll be releasing a new module called the "Footprint Designer" to automate non-standard parts or even standard parts too.
 
You will be able to build any PCB Library part in the industry. Through-hole, Surface Mount, SMT/PTH mix, 50,000 connectors and switches, relays, trim pots, transformers, etc.
 
Our new "Footprint Designer" will allow you to quickly recreate any component mfr. recommended footprint.
 
We're also adding 3D STEP model technology soon.
 
I'm sure that you will like the upcoming updates in 2013.
 
Back to Top
BennsPCB View Drop Down
Advanced User
Advanced User


Joined: 30 Jan 2013
Location: Sweden
Status: Offline
Points: 98 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BennsPCB Quote  Post ReplyReply Direct Link To This Post Posted: 15 Jun 2013 at 9:03am
When will the "Footprint Designer" be released?

/Benn
Back to Top
Tom H View Drop Down
Admin Group
Admin Group
Avatar

Joined: 05 Jan 2012
Location: San Diego, CA
Status: Offline
Points: 5718 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tom H Quote  Post ReplyReply Direct Link To This Post Posted: 15 Jun 2013 at 9:21am
The "Footprint Designer" was created for the V2013 release.
 
V2013.04 is the next release that adds even more features. It should be released by Monday 6/17/13
 
However, Footprint Designer is non-functional in the free "PCB Library Expert Lite" version.
 
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down



This page was generated in 0.188 seconds.